hard start kits,spp5,supco spp6,spp8,hs810,rco410 - HS810

Features Specifications: Hard Start Capacitors
HS410,HS600,HS650,HS810,RCO410,RCO600,RCO650,RCO810,Supco SPP5,SPP6,
SPP7,SPP8,SPP9,SPP5E,SPP6E,SPP7E,SPP8E,SPP9E,

Features Specifications: hard start kit (refrigeration, HVAC)
Features:
1) Increases starting torque up to 500%
2) UL certified
3) Totally solid state integrated design
4) Fast, easy wires installation
5) Three mounting options: Clip, screw, capacitor bracket
6) Individually packed
Replaces: GEM HS600, HS650, HS800, HS410, HS810, SUPCO SPP5, SPP6

Refrigeration spare parts, refrigerator parts, air conditioner spare
parts, hard start kit(SPP5, SPP6, SPP8E, HS410, HS810, and so on),
potential relay, thermostat(Danfoss type, Ranco type, Ego type, Supco
type and so on).

HS810 1/12 thru 1/5 115
HS410 1/4 and 1/3 115
HS600 1/2-5 115
HS650 1/4 and 1/3 115
EVP4E 1/8 - 1 90-130V
EVP5E 1/3 - 2 90-277V
EVP6E 1/2 - 3 90-277V
EVP7E 1 - 4 90-277V
EVP8E 1 - 5 90-277V
EVP9E 1 - 5 90-277V
EVP10E 3 - 5 90-277V

Part no. Horsepower voltage
Hs600 1/2 - 5 277
Hs650 1/2 - 10 277
Hs410 1/4 and 1/3 115
Hs810 1/12 thru1/5 115
Spp8 10 288

Part No. Increased Torque Voltage
SPP5 270 Ounce Inches 115-230
SPP6 390 Ounce Inches 115-230
SPP Series Capacitor Operation Voltage Recommended Range Increase in Torque (%)
SPP5 43-52uf 115-288VAC 1/2HP-10HP 300%
Spp6 130~156 uf 115-288VAC 1/2HP-10HP 500%
SPP8 189-227uf 115-288VAC 1/2HP-10HP 690%
We can apply hard start kit by your requestment.

Part No. Voltage(V) Horsepower(Hp)
HS600 115-277 1/2-5
HS650 115-277 1/2-10
HS410 115-277 1/ 4 and 1/3
HS810 115-277 1/12 thru 1/5
SPP8 120-288 10

This product is used for starting air conditioner or heat
pump compressors (both reciprical and scroll type) that
need an extra "jolt" of electricity to get started. Equipment
that needs a hard-start capacitor:
heat pump or condensers split-systems that have a (TXV)
installed on them.old heat pump or condensers that are mechanically stuck
and not operating

If you have a new or old compressor that isn't starting,
try installing this hard-start capacitor before you do anything
else. The parts inside a compressor might be too physically tight
to move, or on systems with a TXV where the refrigerant pressures
are higher on start-up, and need an extra "kick" of energy to get
started. This hard-start capacitor provides that extra jolt of
energy. Capacitor is very easy to install (takes about 1 minute)
and will remain permanently in the equipment.